Showing posts with label motor trade. Show all posts
Showing posts with label motor trade. Show all posts

Friday 30 November 2012

The smell of burning!


Overheated rear brake disc.
I was in a hurry the other day to get the dog to the vet. It was not until I was part way up the bypass that I realised that the handbrake had stuck on. Even though the hand brake leaver in the cab was completely off, the smell of brake linings was overpowering. It's just as well the vets was not too far, even so the back wheels were so hot you could not touch them. Just before we made the return journey I slipped under the van and pulled back the little arms that operate the handbrake on the back of the callipers. Man, they we tight! This does not bode well for those new wheel bearings that were fitted earlier in the year. A sticking hand brake is one of the reasons why the bearing failed in the first place!
 

Showing handbrake arm on Calliper
With the back of the van up in the air and both the wheels off, it is time to get to grips with sorting this problem out. On further investigation it turns out that the shaft that sticks out of the back of the calliper with the handbrake actuation arm on, has rusted tight. Even though there is a little rubber cup that sits between the calliper and the arm to protect the shaft from the weather. I believe this is its downfall because once the water gets behind the seal it remains there helping the rust to build up causing it to seize. 

 
Once the handbrake cable has been loosened you can remove the end of the cable from the arm more easily, with a bit of fiddling. To free the arm off you will need to tap it backwards and forwards with a medium weight hammer. Do not over do the amount of force you use when hitting the arm with the hammer. The idea is not to do it in one hit but to keep moving it up and down until the sprung loaded arm moves back to the off position on its own. When it feels like it has freed off enough to move it easily by hand, you need to check it's at the off position. If not, it is time to take a closer look at the spring. If the metal of the spring is pitted and heavily rusted it is possible that it has lost some of its tension. For the three or so pounds each it costs to replace these springs it is not worth messing about. Removing the spring from the arm is a bit annoying but straight forward with a pair of pliers.

Handbrake arm spring old and new

 
There is one last thing to do as a suggestion before you box it up and that is to get some white grease and push it in behind the little rubber seal that protects the handbrake arm shaft this will help to keep things moving and the weather out.

 
I have used this method on my van and so far, the hand brake has not stuck on again.


 
Related post   rear wheel bearing replacement.
 

 

 


Tuesday 4 September 2012

Vivaro couldn't pull the skin off a rice pudding.


The van has developed a running fault that started a month or so ago and has become progressively worse. It has taken us some time to chase down the cause of this problem.


The symptoms:

 This fault shows it's self when you drive away from a stand still. You have to push down the accelerator pedal a lot further than is normal to get it to speed up enough to change up to second gear. On lifting your foot off the accelerator pedal to change gear the vehicle speeds up while you are changing up. On pressing down on the pedal again the van struggles to gain speed. It feels like it is holding back.

 
Thought process and action.
 
This suggests that it is a fuel problem. But it has nothing to do with fuel, injectors, high pressure pump, fuel filter or related sensors. Another suggestion was the turbo, but we could hear it spooling up. We checked the turbo pipes, ducting was tight and not blocked. We found a couple of lose hose clips but not enough to cause power loss. Also checked to make sure the waste gate solenoid worked as it should.

At one point we thought the ECU needed a re-boot, again it did not seem likely. Thinking about it, it was a flow problem the only other thing that came to mind was the air flow meter. Before we paid out on a new meter we surfed some motoring forums for pointers, but no one had this fault it would seem. We came across a thread that suggested the changing of the airflow meter would sort it out, but this gentleman also had the crank sensor replace. After a short discussion we decided to go with the air flow meter. Bingo! got it in one and what a relief, it would have been an expensive mistake otherwise.


Air flow meter
 

Extra work.

 
While we had the air filter housing off, which is a pig remove, we thought it prudent to check the glow plugs as it only takes a couple of minutes with a voltmeter. We found that two of the plugs didn't work. The ERG valve drew my attention because the inlet manifold was covered in oil suggesting the gasket had failed or the bolts were loose. You have to be patient when removing it as it has a build-up of oil residue. On removal, it was found clogged with a thick coagulated oil that took a bit of cleaning up.
 

It runs and pulls like a train now. The rice pudding skin doesn't stand a chance!